preps
Page 1 of 2 12 LastLast
Results 1 to 10 of 16

Thread: Direct injection on a Cobra 142 GTL

  1. #1
    Join Date
    Sep 2016
    Location
    Central KY
    Posts
    161
    Thanks
    16
    Thanked 41 Times in 31 Posts
    Downloads
    16
    Uploads
    0

    Direct injection on a Cobra 142 GTL

    Is it possible to do a direct injection mod on a 142 gtl? I would buy a 2000 gtl or a 148 but I can't afford it right now. Any help would be very helpful.


    Sent from my iPhone using Tapatalk
    Happy DXing

  2. #2
    Join Date
    Nov 2011
    Location
    North NJ
    Posts
    563
    Thanks
    13
    Thanked 458 Times in 110 Posts
    Downloads
    166
    Uploads
    829

    My Social Networking

    Follow doughboy On Twitter Add doughboy on Facebook
    Visit doughboy's Youtube Channel
    Get a 1/8" Phono Jack or 1/4" or rca jack mount in back of radio get yourself a small piece of coax or shielded audio cable cable Center to Positive of the Phono Jack etc.. cable Shield or Braid to Negative of the Phono Jack etc..


    other end of that cable Find capacitor c119 center conductor of audio cable to positive side where c119 was ground shield of audio cable to a nearby ground pretty much the same as 148 injection

  3. The Following User Says Thank You to doughboy For This Useful Post:

    mattsowders1989 (12-01-2016)

  4. #3
    Join Date
    Nov 2011
    Location
    North NJ
    Posts
    563
    Thanks
    13
    Thanked 458 Times in 110 Posts
    Downloads
    166
    Uploads
    829

    My Social Networking

    Follow doughboy On Twitter Add doughboy on Facebook
    Visit doughboy's Youtube Channel
    also if you get hum or rf noise you can add a small capacitor at the end of the cable before going into the c174 location to filter off the noise

  5. The Following User Says Thank You to doughboy For This Useful Post:

    mattsowders1989 (12-01-2016)

  6. #4
    Join Date
    Sep 2016
    Location
    Central KY
    Posts
    161
    Thanks
    16
    Thanked 41 Times in 31 Posts
    Downloads
    16
    Uploads
    0
    What about keying up? I guess I should use the transmit pin and ground for keying? I've seen people make a box for it.


    Sent from my iPhone using Tapatalk
    Happy DXing

  7. #5
    Join Date
    Nov 2011
    Location
    North NJ
    Posts
    563
    Thanks
    13
    Thanked 458 Times in 110 Posts
    Downloads
    166
    Uploads
    829

    My Social Networking

    Follow doughboy On Twitter Add doughboy on Facebook
    Visit doughboy's Youtube Channel
    Yeah you just use the regular mic jack ground and tx pin with a foot switch or button or even an old mic I don't member if that radio needs a receive pin or not unplug the mic if you still her receive your golden if not use and old mic or switch from a mic to rig up something

  8. The Following User Says Thank You to doughboy For This Useful Post:

    mattsowders1989 (12-01-2016)

  9. #6
    Join Date
    Sep 2016
    Location
    Central KY
    Posts
    161
    Thanks
    16
    Thanked 41 Times in 31 Posts
    Downloads
    16
    Uploads
    0
    Cool. Thanks doughboy!!!


    Sent from my iPhone using Tapatalk
    Happy DXing

  10. #7
    Join Date
    Sep 2016
    Location
    Central KY
    Posts
    161
    Thanks
    16
    Thanked 41 Times in 31 Posts
    Downloads
    16
    Uploads
    0
    i cant find c119 for the life of me. when i do find it, do i need to remove it?
    Happy DXing

  11. #8
    Join Date
    Nov 2011
    Location
    North NJ
    Posts
    563
    Thanks
    13
    Thanked 458 Times in 110 Posts
    Downloads
    166
    Uploads
    829

    My Social Networking

    Follow doughboy On Twitter Add doughboy on Facebook
    Visit doughboy's Youtube Channel
    It should be not to far from ic4 ic4 is marked ta7222p also near tr35 and yes you remove then you audio feed goes in hole where positive leg was cap will be marked so you can see positive pin

  12. The Following User Says Thank You to doughboy For This Useful Post:

    mattsowders1989 (12-05-2016)

  13. #9
    Join Date
    Nov 2011
    Location
    North NJ
    Posts
    563
    Thanks
    13
    Thanked 458 Times in 110 Posts
    Downloads
    166
    Uploads
    829

    My Social Networking

    Follow doughboy On Twitter Add doughboy on Facebook
    Visit doughboy's Youtube Channel
    Did you find it look at the pic in this URL it's on the right side you'll see a large chip heatsinked to the side that's the audio chip slightly toward the back from that there's a large cap it will be somewhere in that area

    https://www.google.com/search?q=cobr...xXUG-0PQ2TM%3A

  14. #10
    Join Date
    Sep 2016
    Location
    Central KY
    Posts
    161
    Thanks
    16
    Thanked 41 Times in 31 Posts
    Downloads
    16
    Uploads
    0
    ok. i did exactly what you said but i get no audio from the cable i ran. i ran from positive side of c119 and grounded the other. am i missing something? i key up the radio and send signal into the newly installed audio line but nothing comes out
    Happy DXing

Visitors found this page by searching for

http:www.cbjunkies.comthreads1804-Direct-injection-on-a-Cobra-142-GTL

cobra 148 gtl direct injection

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •